Electric motors and generators; DC, of an output exceeding 750W but not exceeding 75kW8501.32

Of an output exceeding 750|W but not exceeding 75|kW

For use in civil aircraft

Solar chargers that consist of less than six cells, are portable and supply electricity to devices or charge batteries; thin film photovoltaic products; crystalline silicon photovoltaic products that are permanently integrated into electrical goods, where the function of the electrical goods is other than power generation, and where these electrical goods consume the electricity generated by the integrated crystalline silicon photovoltaic cell(s); modules or panels with a output voltage not exceeding 50 V DC and a power output not exceeding 50 W solely for direct use as battery chargers in systems with the same voltage and power characteristics

Other

DC motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more,

DC motor with or without commutator, with -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more, for driving hand-held power tools or lawn mowers

Other

Consigned from the People's Republic of China, unless the products are in transit in the sense of Article V GATT (http://www.wto.org/english/docs_e/legal_e/gatt47_01_e.htm)

Crystalline silicon photovoltaic modules or panels

Consigned from Malaysia

Consigned from Taiwan

Automotive-ready, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12V), -a flange diameter of 85 mm or more, but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller

Other

Fuel cell module containing at least polymer electrolyte membrane fuel cells whether or not in a housing with an integrated cooling system, for use in the manufacture of motor vehicle propulsion systems

Automotive-ready, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12V), -a flange diameter of 85 mm or more but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley, -whether or not with rotor position sensor

Other

Traction motor, with: -|a torque output of 200|Nm or more but not more than 300|Nm -|a power output of 50|kW or more but not more than 100|kW -|a speed of not more than 12|500|rpm for use in the manufacture of electric vehicles

Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12 V), or with a minimum output of 750 W but not more than 1,55 kW (at 36 V), -a flange diameter of 85 mm or more but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley, -whether or not with rotor position sensor

Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor

Automotive-ready, brushless and permanently excited direct current motor with: -|a specified speed of not more than 4|000|rpm, -|a minimum output of 400|W, but not more than 1,3|kW (at 12V), -|a flange diameter of 90|mm or more, but not more than 150|mm, -|a maximum length of 190|mm, measured from the beginning of the shaft to the outer ending, -|a housing length of not more than 150|mm, measured from the flange to the outer ending, -|a two-piece (basic housing including electric components and flange with minimum 2|and maximum 6|bore holes) aluminium diecast housing with a sealing compound (groove with an O-ring and grease), -|a stator with single T-tooth design and single coil windings in 12/8|topology and -|surface magnets

Automotive-ready, brushless and permanently excited direct current motor with: -|a specified speed of not more than 4|100|rpm, -|a minimum output of 400|W, but not more than 1,3|kW (at 12V), -|a flange diameter of 90|mm or more, but not more than 150|mm, -|a maximum length of 200|mm, measured from the beginning of the shaft to the outer ending, -|a housing length of not more than 160|mm, measured from the flange to the outer ending, -|a maximum of two-piece (basic housing including electric components and flange with minimum 2|and maximum 6|bore holes) aluminium diecast housing whether or not with a sealing compound (groove with an O-ring and grease), -|a stator with single T-tooth design and single coil windings in 12/8|topology, and -|surface magnets

Automotive-ready, brushless and permanently excited direct current motor with: -|a specified speed of not more than 4|100|rpm, -|a minimum output of 400|W, but not more than 1,3|kW (at 12V), -|a flange diameter of 90|mm or more, but not more than 150|mm, -|a maximum length of 210|mm, measured from the beginning of the shaft to the outer ending, -|a housing length of not more than 160|mm, measured from the flange to the outer ending, -|a maximum of two-piece (basic housing including electric components and flange with minimum 2|and maximum 11|bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -|a stator with single T-tooth design and single coil windings in 9/6|or 12/8|topology and -|surface magnets

Other