Electric motors and generators; DC, of an output not exceeding 750W8501.31

Other DC motors; DC generators, other than photovoltaic generators

Other DC motors; DC generators, other than photovoltaic generators

Other DC motors; DC generators

Other DC motors; DC generators, other than photovoltaic generators

Of an output not exceeding 750|W

Motors of an output exceeding|735|W, DC generators, for use in civil aircraft

For use in certain types of aircraft

DC motors, brushless, with: -|an external diameter of 80|mm or more, but not more than 100|mm, -|a supply voltage of 12|V, -|an output at 20|°C of 300|W or more, but not more than 750|W, -|a torque 20|°C of 2,00|Nm or more, but not more than 7,00|Nm, -|a rated speed at 20|°C of 600|rpm or more, but not more than 3|100|rpm, -|with or without the rotor angle position sensor of resolver type or Hall effect type, of the kind used in power steering systems for cars

Other

DC motor, brushless, with a three-phase winding, an external diameter of 85|mm or more, but not exceeding 115|mm, a nominal torque of 2.23|Nm (±|1.0|Nm), of an output of more than 120|W but not exceeding 520|W, calculated with 1550|RPM (±|350|RPM) at a supply voltage of 12|V equipped with electronic circuit with sensors using the Hall effect, for use with an electric power steering control module (power steering motor)

Brushless DC motor assembly comprised of a motor and transmission, with: -|an electronic control operating by| Hall Effect position sensors, -|a voltage input 9|V or more but not more than 16|V, -|an external diameter of|70|mm or more but not more than 80|mm, -|an output motor power 450|W or more but not more than 500|W, -|a maximum output|torque 50|Nm or more but not more than 52|Nm, -|a maximum output rotation speed 280|rpm or more but not more than 300|rpm, -|a coaxial male spline outputs with an outer diameter of 20|mm (±1|mm), 17|teeth and a minimum length of the teeth of|25|mm|(± 1|mm), and -|a distance between root of splines of 119|mm (± 1|mm) for use in the manufacture of all-terrain|or utility task vehicles

Automotive-ready, brushless and permanently excited direct current motor with: -|a specified speed of not more than 4|000|rpm, -|a minimum output of 400|W, but not more than 1,3|kW (at 12V), -|a flange diameter of 90|mm or more, but not more than 150|mm, -|a maximum length of 190|mm, measured from the beginning of the shaft to the outer ending, -|a housing length of not more than 150|mm, measured from the flange to the outer ending, -|a two-piece (basic housing including electric components and flange with minimum 2|and maximum 6|bore holes) aluminium diecast housing with a sealing compound (groove with an O-ring and grease), -|a stator with single T-tooth design and single coil windings in 12/8|topology and -|surface magnets

Permanently excited DC motor with - a multiple-phase winding, - an external diameter of 30 mm or more but not more than 90 mm, including mounting flange, - a rated speed of not more than 15 000 rpm, - an output of 45 W or more but not more than 400 W, and - a supply voltage of 9 V or more but not more than 50 V, - whether or not with a drive disc, - whether or not with a crankcase, - whether or not with a fan, - whether or not with a cap assembly, - whether or not with a sun gear, - whether or not with a speed and rotational direction encoder, - whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, - whether or not with a mounting flange

Permanently excited DC motor with -|a multiple-phase winding, -|an external diameter of 30|mm or more but not more than 80|mm, -|a rated speed of not more than 15|000|rpm, -|an output of 45|W or more but not more than 300|W and -|a supply voltage of 9|V or more but not more than 50|V -|whether or not with a drive disc -|whether or not with a crankcase -|whether or not with a fan -|whether or not with a cap assembly -|whether or not with a sun gear -|whether or not with a speed and rotational direction encoder -|whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type

Permanently excited DC-motor with • a multiple-phase winding, • an external diameter of 30mm or more, but not more than 80mm, • a rated speed of not more than 15000 rpm, • an output of 45W or more, but not more than 300W and • a supply voltage of 9V or more, but not more than 25V

Permanently excited DC motor with -|a multiple-phase winding, -|an external diameter of 30|mm or more but not more than|80|mm, -|a rated speed of not more than 15|000|rpm, -|an output of 45|W or more but not more than 300|W and -|a supply voltage of 9|V or more but not more than 25|V

Automotive-ready, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12V), -a flange diameter of 85 mm or more but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley, -whether or not with rotor position sensor

Other

DC motors, brushless, with: -|an external diameter of 90|mm or more, but not more than 110|mm, -|a rated speed of not more than 3|680|rpm, -|an output of 600|W or more but not more than 740|W at 2|300|rpm and at 80|°C, -|a supply voltage of 12|V, -|a torque of not more than 5,67|Nm, -|a rotor position sensor, -|an electronic star-point relay, and -|for use with an electric power steering control module

Motor for automotive electric seat adjustment applications: -with a shaft output on both motor sides, -consisting of a permanently excited DC motor,  -whether brushed or brushless,  -whether or not with electronic control unit,  -whether or not with Hall Effect Sensor,  -with a nominal voltage of 8 V or more but not more than 16 V,  -with a rated output mechanical power not exceeding 120 W, and -with a specified temperature range from -40 °C to 160 °C,  for use in the manufacture of automotive components for car's seats

Brushless DC electric motors:  -with a rated power of 240 W or more, but not more than 260 W,  -with a voltage of 36 V or higher, but not higher than 52 V  -with a torque of 20 Nm or more, but not more than 140 Nm,  -with a housing made of aluminum, aluminum alloy or plastic,  -with or without a built-in controller,  -with a communication function in the LIN or UART interface,  -weighing 1,5 kg or more, but not more than 5,0 kg,  -adapted for mounting in a bicycle frame  for use in the manufacture of e-bikes

Brushless DC electric motors: - with a rated power of 240 W or more, but not more than 260 W, - with a voltage of 24 V or higher, but not higher than 52 V, - with a torque of 30 Nm or more, but not more than 62 Nm, - with a LIN, UART or CAN communication interface, - with an internal planetary gearbox with fixed or variable ratio or direct drive, - with a housing made of aluminum or aluminium alloy, - with a weight of 1,5kg or more, but not more than 6kg, - adapted for mounting in the front or rear bicycle wheel, for use in the manufacture of e-bikes

Brushless DC electric motors:  -with a rated power of 240 W or more, but not more than 260 W,  -with voltage of 36 V or higher, but not higher than 52 V,  -with torque of 30 Nm or more, but not more than 50 Nm,  -with communication function UART or CAN interface,  -with internal planetary gearbox with fixed or variable ratio,  -made by CNC machined casting,  -with housing made of aluminum,  -weighing 2,3 kg or more, but not more than 4,4 kg, -adapted for mounting in the front or rear bicycle wheel

DC motors, brushless, with:| -|an external diameter of 80|mm or more, but not more than 200|mm, -|a supply voltage of 9|V or more, but not more than 16|V, -|an output at 20|°C of 300|W or more, but not more than 750|W, -|a torque at 20|°C of 2,00|Nm or more, but not more than 7,00|Nm, -|a rated speed at 20|°C of 600|rpm or more, but not more than 3|100|rpm, -|with or without the rotor angle position sensor of resolver type or Hall effect type, of the kind used in power steering systems for cars

DC motors, brushless, with:| -|an external diameter of 80|mm or more, but not more than 200|mm, -|a supply voltage of 4|V or more, but not more than 16|V, -|an output at 20|°C of 200|W or more, but not more than 750|W, -|a torque at 20|°C of 2,00|Nm or more, but not more than 7,00|Nm, -|a rated speed at 20|°C of 600|rpm or more, but not more than 3|100|rpm, -|with or without a pulley, - with or without an electronic power steering sensor/controller

DC motors, brushless, with:| -|an external diameter of 80|mm or more, but not more than 200|mm, -|a supply voltage of 9|V or more, but not more than 16|V, -|an output at 20|°C of 300|W or more, but not more than 750|W, -|a torque at 20|°C of 2,00|Nm or more, but not more than 7,00|Nm, -|a rated speed at 20|°C of 600|rpm or more, but not more than 3|100|rpm, -|with or without a pulley, - with or without an electronic power steering sensor/controller

DC motors, brushless, with:| -|an external diameter of 80|mm or more, but not more than 200|mm, -|a supply voltage of 9|V or more, but not more than 16|V, -|an output at 20|°C of 300|W or more, but not more than 750|W, -|a torque at 20|°C of 2,00|Nm or more, but not more than 7,00|Nm, -|a rated speed at 20|°C of 600|rpm or more, but not more than 3|100|rpm, -|with or without the rotor angle position sensor of resolver type or Hall effect type, - with or without a pulley, of the kind used in power steering systems for cars

Electric brushless direct current motor finished with biocompatible materials such as stainless steel according to specification 17-4 PH or type 303, 316L, 400 with: -a three-phase winding, -an output power not exceeding 280 W, -a length with gearhead of 116,1 mm or more but not more than 117,2 mm, -an external diameter of 13,86 mm or more but no more than 13,92 mm, -a maximum torque of motor with gearhead 246,6 mNm in 25℃, -a no-load radial speed of motor with gearhead with 9 900 rpm, at 24V in 25°C, -a weight of motor with gearhead of 70,5 g or more but not more than 71,5 g, a resistance to peak temperature of 140°C or more (non-operating), a maximal air leak between shaft and shaft seals of 15 Pa/s at given 2 Bars of pressure, -14 functional pins for power and control purpose, -a flexible printed circuit with length of 245 mm but no longer than 255 mm with mounted 8 pin male connector for use in the manufacture of medical devices with right-left rotation and oscillation function

Automotive-ready, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12V), -a flange diameter of 85 mm or more, but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller

Brushless DC electric motor, with: -a rated voltage of 310 V, -a rated power of 350 W or more but not more than 368 W, -an input power of 500 W or more but not more than 550 W, -output power of 350 W or more but not more than 400 W, -an external diameter without bracket connector and pulley of 143,2 mm or more but not more than 143,8 mm, -a rated speed of 16300 rpm or more but not more than 16500 rpm, -a weight of 2,33 kg or more but not more than 2,40 kg, -a pulley

Brushless DC electric motor, with: -a rated voltage of 310 V, -a rated power of 350 W or more but not more than 368 W, -an input power of 500 W or more but not more than 550 W, -output power of 350 W or more but not more than 400 W, -an external diameter without bracket connector and pulley of 143,2 mm or more but not more than 143,8 mm, -a rated speed of 16300 rpm or more but not more than 16500 rpm, -a weight of 2,33 kg or more but not more than 2,40 kg, -a pulley

DC motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more,

DC motor with or without commutator, with -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more, for driving hand-held power tools or lawn mowers

DC motor with commutator, with -|an external diameter of 27.5|mm or more, but not more than 45|mm, -|a rated speed of 11|000|rpm or more, but not more than 23|200|rpm, -|a rated supply voltage of 3.6|V or more, but not more than 230|V, -|an output power of not more than 529|W, -|a free load current of not more than 3.1|A, -|a maximum efficiency of 54|% or more, for driving hand-held power tools

DC motor, brushless, integrated with an Electronic Control Unit (ECU), defined as a Power Pack with: -a safety feature and mechanism designed for prevention of critical hazards like self-steer by single failure, -a CAN-communication interface, -an external sensor interface, -operating temperature range of -40℃ to 95℃ or broader, -compliance with standard IP6K9K for water and dustproofness, -supply voltage of 9 V or more, but not more than 16 V, -rated power output of 500 W or more, but not higher than 750 W, -rated torque of 3 Nm or more, but not more than 6 Nm, -length of 150 mm or more, but not more than 250 mm, -width of 100 mm or more, but not more than 150 mm, -height of 80 mm or more, but not more than 120 mm

Brushless DC electric motor with LCD control indicator and/or control unit with buttons: -with an output power of 200 W or more, but not more than 700 W, -with a supply voltage of 30 V or more, but not more than 60 V, -with a torque of 30 Nm or more, but not more than 200 Nm, -with a height of 117 mm or more, but not more than 146 mm, -with a length of 117 mm or more, but not more than 223 mm, -with a width of 135 mm or more, but not more than 190 mm, -with a weight of 2 kg or more but not more than 5 kg, -designed to be mounted in a frame, front or rear bicycle wheel, -equipped with sockets, at least for cable connection with LCD control indicator, for use in the manufacture of electric bicycles

Permanently excited DC motor with: -an external diameter of 30 mm or more but not more than 90 mm, including mounting flange, -a rated speed of not more than 15 000 rpm, -an output of 45 W or more but not more than 400 W, and -a supply voltage of 9 V or more but not more than 50 V, -whether or not a multiple-phase winding, -whether or not with a drive disc, -whether or not with a crankcase, -whether or not with a fan, -whether or not with a cap assembly, -whether or not with a sun gear, -whether or not with a speed and rotational direction encoder, -whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, -whether or not with a mounting flange

Permanently excited DC motor with: -an external diameter of 27 mm or more but not more than 90 mm, including mounting flange, -a rated speed of not more than 25 000 rpm, -an output of 45 W or more but not more than 400 W, and -a supply voltage of 9 V or more but not more than 50 V, -whether or not a multiple-phase winding, -whether or not with a drive disc, -whether or not with a crankcase, -whether or not with a fan, -whether or not with a cap assembly, -whether or not with a sun gear, -whether or not with a speed and rotational direction encoder, -whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, -whether or not with a mounting flange for use in the manufacture of air suspension seats in tractors, earthmoving machines and forklifts or for use in the manufacture of actuators for height-adjustable furniture

Permanently excited DC motor with: -an external diameter of 30 mm or more but not more than 90 mm, including mounting flange, -a rated speed of not more than 15 000 rpm, -an output of 45 W or more but not more than 400 W, and -a supply voltage of 9 V or more but not more than 50 V, -whether or not a multiple-phase winding, -whether or not with a drive disc, -whether or not with a crankcase, -whether or not with a fan, -whether or not with a cap assembly, -whether or not with a sun gear, -whether or not with a speed and rotational direction encoder, -whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, -whether or not with a mounting flange for use in the manufacture of air suspension seats in tractors, earthmoving machines and forklifts or for use in the manufacture of actuators for height-adjustable furniture

Brushless DC motor that can revolve counter clockwise (CCW), with: -|an input voltage of 264|V or more, but not more than 391|V, -|an external diameter of 81|mm (± 2,5|mm) or more, but not more than 150|mm (± 0,8|mm), -|an output power of not more than 125|W, -|E or B class winding insulation,for use in the manufacture of indoor or outdoor units of split-type air conditioning machines

Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12 V), or with a minimum output of 750 W but not more than 1,55 kW (at 36 V), -a flange diameter of 85 mm or more but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley, -whether or not with rotor position sensor

Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor

Fuel cell module containing at least polymer electrolyte membrane fuel cells whether or not in a housing with an integrated cooling system, for use in the manufacture of motor vehicle propulsion systems

Fuel cell module containing at least polymer electrolyte membrane fuel cells in a housing with an integrated cooling system, for use in the manufacture of motor vehicle propulsion systems

Camshaft actuator for controlling the timing of valve opening by using electromotor in a continuous variable valve timing system of an internal combustion piston engine, of: -a length of 110 mm or more but not more than 140 mm, -a width of 90 mm or more but not more than 130 mm, -a height of 80 mm or more but not more than 110 mm for use in the manufacture of engines of motor vehicles

DC motors,|brushless, with:| -|an external diameter of 80|mm or more, but not more than 100|mm, -|a supply voltage of 12|V, -|an output at|20|°C of 300|W or more, but not more than 550|W, -|a torque 20|°C of 2,90|Nm or more, but not more than 5,30|Nm, -|a rated|speed at 20|°C of 600|rpm or more, but not more than 1|200|rpm, -|equipped with the rotor angle position sensor of resolver type or Hall effect type, of the kind used in|power steering systems for cars

DC motors, brushless, with: -|an external diameter of 80|mm or more, but not more than 100|mm, -|a supply voltage of 12|V, -|an output at 20|°C of 300|W or more, but not more than 650|W, -|a torque at 20|°C of 2,00|Nm or more, but not more than 5,30|Nm, -|a rated speed at 20|°C of 600|rpm or more, but not more than 3|100|rpm, -|equipped with the rotor angle position sensor of resolver type or Hall effect type, of the kind used in power steering systems for cars

Automotive-ready, brushless and permanently excited direct current motor with: -|a specified speed of not more than 4|100|rpm, -|a minimum output of 400|W, but not more than 1,3|kW (at 12V), -|a flange diameter of 90|mm or more, but not more than 150|mm, -|a maximum length of 210|mm, measured from the beginning of the shaft to the outer ending, -|a housing length of not more than 160|mm, measured from the flange to the outer ending, -|a maximum of two-piece (basic housing including electric components and flange with minimum 2|and maximum 11|bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -|a stator with single T-tooth design and single coil windings in 9/6|or 12/8|topology and -|surface magnets

Solar chargers that consist of less than six cells, are portable and supply electricity to devices or charge batteries; thin film photovoltaic products; crystalline silicon photovoltaic products that are permanently integrated into electrical goods, where the function of the electrical goods is other than power generation, and where these electrical goods consume the electricity generated by the integrated crystalline silicon photovoltaic cell(s); modules or panels with a output voltage not exceeding 50 V DC and a power output not exceeding 50 W solely for direct use as battery chargers in systems with the same voltage and power characteristics

Brushless DC motor assembly comprised of a motor and transmission, with: -|electronic control operating by Hall Effect position sensors, -|voltage input 9V or more but not more than 16V, -|external diameter of the motor 70|mm or more but not more than 80|mm, -|output motor power| 350|W or more but not more than 550W, -|maximum output torque 50|Nm or more but not more than 52|Nm, -|maximum output rotation speed 280|rpm or more but not more than 300|rpm, -|coaxial male spline outputs of outer diameter| 20|mm (±1|mm), 17|teeth and minimum length of teeth 25|mm (± 1|mm), and -|with distance between root of splines 119|mm (± 1|mm) for use in the manufacture of all-terrain or utility task vehicles

Automotive-ready, brushless and permanently excited direct current motor with: -|a specified speed of not more than 4|100|rpm, -|a minimum output of 400|W, but not more than 1,3|kW (at 12V), -|a flange diameter of 90|mm or more, but not more than 150|mm, -|a maximum length of 200|mm, measured from the beginning of the shaft to the outer ending, -|a housing length of not more than 160|mm, measured from the flange to the outer ending, -|a maximum of two-piece (basic housing including electric components and flange with minimum 2|and maximum 6|bore holes) aluminium diecast housing whether or not with a sealing compound (groove with an O-ring and grease), -|a stator with single T-tooth design and single coil windings in 12/8|topology, and -|surface magnets

Electronic actuator consisting of: - a DC motor having a power of less than 600 W, - for usage with a supply voltage of 12 V to 48 V, - with motor connection (plug-in connection), - with contactless position sensor, - built in a rectangular housing of a width of less than 100 mm and a length of less than 150 mm, with reduction gear and lever attached to the motor drive shaft or - in a cylindrical housing of a length off less than 150mm and with a diameter of less than 100 mm, with threads integrated into the rotor of the motor for linear movement of the integrated control rod

Other

Consigned from the People's Republic of China, unless the products are in transit in the sense of Article V GATT (http://www.wto.org/english/docs_e/legal_e/gatt47_01_e.htm)

Crystalline silicon photovoltaic modules or panels

Consigned from Malaysia

Consigned from Taiwan

Power transmission device for controlling the output of exhaust gas turbochargers, consisting of: - a DC motor of an output not exceeding 600 W, - for usage with a supply voltage of 8 V or more but no more than 48 V, - with motor connection (plug-in connection), - whether or not with position sensor, - whether or not with integrated control and power electronics, - whether or not with spring mechanism for resetting the lever, - built in a housing with reduction gear and lever attached to the motor drive shaft, or - built in a housing with threads integrated into the rotor of the motor for linear movement of the integrated control rod

Other

Other