Propylene, other olefin polymers; polypropylene in primary forms3902.10

Polypropylene

Polypropylene containing no plasticizer and not more than: -|7|mg/kg of aluminium, -|2|mg/kg of iron, -|1|mg/kg of magnesium, -|8|mg/kg of chloride

Polypropylene, containing no plasticiser, -|of a melting point of more than 150|°C (as determined by the ASTM D 3417|method), -|of a heat of fusion of 15|J/g or more but not more than 70|J/g, -|of an elongation at break of 1|000|% or more (as determined by the ASTM D 638|method), -|of a tensile modulus of 69|MPa or more but not more than 379|MPa (as determined by the ASTM D 638|method)

Polypropylene, containing not more than 1|mg/kg of aluminium, 0,05|mg/kg of iron, 1|mg/kg of magnesium and 1|mg/kg of chloride, for use in the manufacture of packaging for disposable contact lenses

Polypropylene, containing no plasticiser: -|of a tensile strength: of 32-60|MPa (as determined by the ASTM D638|method);| -|of a flexural strength of 50-90|MPa (as determined by the ASTM D790|method);| -|of a Melt Flow Rate (MFR)|at 230|°C/ 2,16|kg|of 5-15|g/10|min (as determined by the ASTM D1238|method);| -|with 40|% or more but not more than 80|% by weight of polypropylene, -|with 10|% or more but not more than 30|% by weight of glass fibre, -|with 10|% or more but not more than 30|% by weight of mica

Polypropylene, containing no plasticiser: -of a tensile strength: of 32-77 MPa (as determined by the ASTM D638 method);  -of a flexural strength of 50-105 MPa (as determined by the ASTM D790 method);  -of a Melt Flow Rate (MFR) at 230 °C/ 2,16 kg of 5-15 g/10 min (as determined by the ASTM D1238 method);  -with 40 % or more but not more than 80 % by weight of polypropylene, -with 10 % or more but not more than 30 % by weight of glass fibre, -with 10 % or more but not more than 30 % by weight of mica

Polypropylene, containing no plasticizer: • of a tensile strength: of 32-60MPa (as determined by the ASTM D638 method); • of a flexural strength of 50-90MPa (as determined by the ASTM D790 method); • of a Melt Flow Rate (MFR) at 230°C/ 2,16kg of 5-15g/10 min (as determined by the ASTM D1238 method); • with 40% or more but not more than 80% by weight of polypropylene, • with 10% or more but not more than 30% by weight of glass fibre, • with 10% or more but not more than 30% by weight of mica

High isotactic polypropylene (HIPP), whether or not coloured, intended for the manufacture of plastic components for air freshener with the following properties: -|a density of 0,880|g/cm$3|or more but not more than 0,913|g/cm$3(as determined by test method ASTM D1505), -|a tensile strength at yield of 350|kg/cm$2|or more but not more than 390|kg/cm$2|(as determined by test method ASTM D638) -|a heat deflection temperature of 135|°C or more under load of 0,45|MPa|(as determined by test method ASTM 648)

Other